Skip to content

A free in-home estimate and code rules made plain: (562) 379-6735

La Habra Heights · Fullerton · Whittier · La Habra

(562) 379-6735

ServicesWindow Retrofitting

Window Retrofitting in La Habra Heights

Retrofitting puts new, energy-rated windows into your existing frames, so the stucco outside and the drywall inside are left alone. We handle the permit when one is needed, check every opening against current code, and clean each room before we move on.

Installer in a cap caulking the edge of a new white vinyl window set inside an old wood frame on a stucco house wall, aluminum ladder nearby

New Glass Without Opening the Walls

With a retrofit, the old frame stays anchored where it has always been. We lift out the worn sashes and glass, prepare the frame, and set a new unit made to fit inside it. Because nothing is cut away from the exterior wall, there is no stucco patch to blend and no fresh paint line around each window. Inside, the dust stays modest and the work moves room by room.

This approach suits frames that are still healthy: square corners, no soft wood, and no water marks on the sill or the wall beneath it. Older aluminum sliders sitting in solid frames are a common and very good fit. If a frame has rotted or shifted, or you would like a larger or differently shaped opening, we will say so directly and walk you through window replacement or new window installation as the better path.

Part of Every Retrofit Job

Careful measurements
Each opening is measured in three places for width and three for height, and we order to the smallest reading. Older frames drift out of square over the years, and that small allowance lets the new window sit straight.
Taking out the old sashes
We remove the glass and moving parts by hand, then clear the frame of old caulk, grit and flaking paint so the new unit has a clean bed.
Setting the new unit
Shims bring the window true in both directions before it is fastened through its own frame. Outside, we seal it with a product made to hold up against stucco and strong sun. The gap between the old frame and the new one is filled with a gentle, slow-rising foam that blocks drafts while leaving the frame straight and the sash free to open.
Interior trim and exterior face
A trim profile matched to your current casing finishes the inside edge. On the exterior, a flange covers the old frame face for a clean, even border.
Code paperwork
Where your project needs a permit, we file it. Energy rating stickers stay on the glass until the inspector has reviewed them.
Leaving the house tidy
Floors are covered before tools come out. The old windows, broken glass and packaging go with us when we leave.

When Your Windows Are Telling You It Is Time

  • Sliders that stick or lift off

    On older aluminum units, tired rollers and dented tracks make a window fight you and refuse to lock cleanly. When the surrounding frame is still solid, a retrofit renews every part that moves.

  • Cloudy glass you cannot clean

    Haze trapped between two panes tells you the seal has broken and the insulating gas has leaked out.

  • Afternoon heat in certain rooms

    Single-pane and uncoated glass let a great deal of sun heat through. Low-E glass trims that heat gain, a real difference through a long, dry summer.

  • Moving air near a closed window

    A draft or faint whistle points to failed weatherstripping or a loose sash. Both disappear with a new unit.

  • Wet frames on cool mornings

    Bare aluminum frames collect condensation, and over the years that water stains sills and lifts paint.

From First Visit to Final Walkthrough

  1. 1

    A look at every frame

    We come to your home, check each frame for rot, staining or movement, and take measurements. You receive a written estimate with every window on its own line, and there is no charge for the visit.

  2. 2

    Filing and ordering

    If the building department needs to be involved, we take care of the filing. We confirm your chosen glass meets California's Title 24 limits for heat loss and solar heat gain, then order windows made to your measurements.

  3. 3

    The installation

    Most houses are finished in one day. We go one room at a time, protecting nearby floors and furniture first, so no opening stays empty for long.

  4. 4

    Inspection and sign-off

    When the city wants to see the work, we book the inspection and attend it. Then we go window by window with you, opening, locking and checking each seal.

Worker seen from behind writing on a clipboard beside a weathered sliding patio door on a wooden back deck, with a ladder, drill and caulk gun nearby

What Shapes Your Retrofit Estimate

Because the walls stay closed, a retrofit typically runs below the cost of full-frame work. Your total comes down to the products you pick and what your openings need. Each window appears as a separate line, so you can see where the money goes.

How many windows, and how big
Wide picture windows and long sliders use more glass and take more care to handle than a typical bedroom window.
Glass and frame selections
Coatings, frame material and tempered glass all change the figure. Code calls for tempered glass in certain places, such as beside doors, near tubs and close to the floor.
How the old frames have held up
Extra preparation, straightening or sealing adds labor. A frame beyond saving calls for a different method altogether.
Reaching the opening
Upper-floor windows, or those above a slope, may need tall ladders or scaffolding and take longer than windows at ground level.

Common Retrofit Questions

Something not covered here? (562) 379-6735

Will I lose any glass area with a retrofit?

A little. The new frame nests inside the old one, so a narrow strip of visible glass is given up along each edge. A slim-profile frame keeps that small, and we bring samples so you can judge it in person before choosing.

Do I need a permit to retrofit windows?

Across much of California, swapping out windows needs a building permit even if the opening stays the same size. We find out what your address requires and handle the filing, which keeps the work on record for a future sale.

What size do bedroom windows need to be?

Code requires each bedroom to have a window large enough for a person to climb through in a fire. We measure the clear opening of every bedroom window before ordering and choose a style that keeps it compliant. Sometimes that means a casement in place of a slider.

Could the inspection lead to other requirements?

It can. California often asks for working smoke and carbon monoxide alarms when window work is inspected. We raise this during the estimate so nothing catches you off guard on inspection day.

Does a retrofit keep water out as well as full-frame work?

Yes, provided the existing frame is sound and the sealing is done with care. If we find water damage or a frame that has moved, we will recommend full-frame replacement instead.

Find Out if Your Frames Are Good Candidates

We will check each window, give you a straight answer on whether a retrofit fits, and explain any paperwork the city needs. Our free in-home estimates come with no sales pressure and no obligation.